iec inlet filters de ge & series 1. de & ge series filters are for ul 544 & ul 2601 health care equipment. 2. de series: ul, csa, vde. 3. ge series: ul, csa, vde. 4. ge series is with optional bleeder resistor and wire connection. introductions 1. maximum leakage current each line-to-ground: @ 115vac 60hz: 2ua 2. hipot rating (one minute) line-to-ground: 2250vdc line-to-line: 1450vdc 3. operating frequency: 50/60hz 4. rated voltage: 115/250vac specifications electrical schematic mechanical construction minimum insertion loss in db components 0.15 40 25 24 12 type frequency-mhz 0.15 25 18 8 3 0.15 30 25 20 7 0.15 30 30 26 14 0.15 10 12 15 5 0.15 10 20 25 20 common mode (l-g) in 50 ohm system current rating 1 3 10 3 10 20 a a 6a a a 6a a a 01, 03, 06,10deeg3bm 03, 06, 10gee3qm 0.84 21.3 1.12 28.4 2.10 1.95 49.5 53.3 1.52 38.6 1.575 0.005 +0.02 +0.02 0.85-0 r0.12 21.6 r3.0 1.12-0 28.45 40.1 m3 52.1 2.05 n g l 0.13 3.3 1.575 0.02 40.01 part no. cx (uf) l (mh) 5 1.8 0.6 0.18 01deeg3bm 03deeg3bm 06deeg3bm 10deeg3bm 03geeg3qm/w3qm 4.0 0.033 1.5 0.1 0.3 03geng3qm/w3qm 06geeg3qm/w3qm 06geng3qm/w3qm 10geeg3qm/w3qm 10geng3qm/w3qm 20geeg3em/w3em 20geng3em/w3em 7-1 de, ge series g n l l i n e l o a d g' n' l' l r cx (r:1m ) eg3bm eg3qm (optional wire type) unit: inch mm * * * ul, csa approved to 4a 115/250v ul, csa approved to 8a 115/250v ul, csa approved to 13a 115/250v vde approved to 16a 250v 01deeg3bm 03deeg3bm 06deeg3bm 10deeg3bm 03geeg3qm/w3qm 03geng3qm/w3qm 06geeg3qm/w3qm 06geng3qm/w3qm 10geeg3qm/w3qm 10geng3qm/w3qm 20geeg3em/w3em 20geng3em/w3em suggested mounting cutout (mounting from reverse) 18 15 6 8 25 20 8 10 25 20 10 12 20 20 10 12 18 20 10 10 5 12 6 6 @ 250vac 50hz: 5ua
mechanical construction unit: inch mm 7-2 1.04 max. r0.118 max. 3.19 max. 1.36 max. 0.248x0.031 0.138 2.60 max. 1.18 66.0 max. 6.3x0.8 34.5 max. 81.0 max. 3.5 30.0 26.5 max. r3.0 max. 26.5-0 +0.5 +0.02 1.043-0 36.0-0 +0.5 1.417-0 +0.02 20geeg3e (optional wire type) 1.043-0 1.04 max. suggested mounting cutout (mounting from reverse) r0.157 max. 34.5-0 +0.5 m3 0.138 0.248x0.031 1.36 max. 3.19 max. 2.60 max. +0.02 1.654 0.004 2.09 1.18 1.654 0.138 66.0 max. 6.3x0.8 34.5 max. 81.0 max. 26.5 max. 3.5 30.0 53.0 3.5 42.0 42.0 0.1 +0.5 26.5-0 r4.0 max. 1.358-0 +0.02 20geng3e (optional wire type) ng3qm (optional wire type) 1.66 m ax. 1.12 max. 0.84 max. 2.08 m ax. 1.22 0.2 1.16 0.004 0.142 +0.04 -0.02 0.945 0.02 0.063 0.85 0.004 0.03 ~ r0.08max(2x) 31.0 0.5 24.0 0.5 -0.5 +1.0 3.6 28.4 max. r2.0max 21.3 max. 42.6 m ax. 52.83 m ax. 29.5 0.1 21.5 0.1 0.76 1.6 ~ suggested thickness of mounting panel is from 0.04 (1.0) to 0.063 (1.6) inch (mm) of mounting cutout 1.12 max. 28.4 max. l' g' n' +0.04 -0.02 1.66 max. 42.16 max. 2.08 max. 0.142 -0.5 +1.0 52.83 max. 3.6 l 1.22 0.02 31.0 0.5 g n 24.0 0.5 0.945 0.02 +0.012 +0.3 1.12 28.45 -0 -0 r0.08max. r2.0max. 0.862 0.004 21.90 0.1 all wire leads 4.0" long min. 21.4max. 0.84max. ng3qm(h) (optional wire type) suggested thickness of mounting panel is from 0.04 (1.0) to 0.063 (1.6) inch (mm) of mounting cutout suggested thickness of mounting panel is from 0.04 (1.0) to 0.063 (1.6) inch (mm) of mounting cutout suggested mounting cutout suggested mounting cutout suggested mounting cutout (mounting from reverse)
|
